Go to footer

Resin Heads on Obitsu Bodies

Patient enough to take us step-by-step through a how-to? Well post it here!

Resin Heads on Obitsu Bodies

Postby K2! » Thu Jan 22, 2015 7:18 am

Attaching a resin head to an Obitsu body is not hard but it does require a little modification to the Obtsu neck piece.

Remove the neck piece from the Obitsu body.

On the inside there is a small Phillips screw. Remove this screw. This will allow you to remove the interior parts of the neck piece.

You will need the body of the neck piece (the large hollow tube part). Put the other neck piece parts away in a safe place in case you wish to restore the neck piece in the future.

Next you will need a piece of stiff wire. You can use a piece of wire snipped from a coat hanger. Cut a piece of wire about 5/8" (1.7cm) long, the diameter of the outside of the neck piece body.

Now you will need to drill a pair of holes in the body of the neck piece. The holes will need to be the same diameter as the thickness of your wire. You might have to take a piece of your wire to a hardware store to find a drill bit that is the right size. You should be able to buy a single drill bit (not a set) that shouldn't cost very much.

Measure down from the top of the neck piece about 1/2" or 1cm. The top of the neck piece is the end with the angled collar that sticks out of the neck vinyl.

At your mark using your wire sized drill bit, drill a hole through the neck piece body, from one side to the other. Continue drilling till you drill through the second side of the tube. This should essentially be across the diameter of the tube.

Now insert your wire into one side and through to the other side of the neck piece. Depending on how well you matched the drill bit to the wire diameter, this may be a snug fit. If so, tap the wire in gently with a hammer. If the wire is loose, a drop of super glue on each end will keep it from moving around.

Now you should have a neck piece tube with a piece of wire running across the middle.
Image

When the glue drys (if you used glue), thread a piece of stringing elastic down through the top of the neck piece, then back up through the neck piece so both ends stick out of the top of the neck piece. You want to make sure the elastic loops around the wire so it doesn't pull out the top. The length of elastic will depend on the brand of head and how the elastic normally terminates in the head. Cut the elastic a bit longer than you think you will need. You can always trim off the extra

Re-inset the neck piece on the Obitsu body and thread the elastic through the neck side of the resin head. Finish off securing the elastic and head as you would normally.
Image
User avatar
K2!
Stoopid Noob
 
Posts: 2648
Joined: Sat Mar 20, 2010 6:31 pm
Location: The Angry Dome


Re: Resin Heads on Obitsu Bodies

Postby Greyhaunt » Thu Jan 22, 2015 2:35 pm

Pardon my tool ignorance, but could I drill a hole like that with a dremel? Do they make drill bits of this type for them?
Image
User avatar
Greyhaunt
Snarky Bitch Who Runs this Place
 
Posts: 3680
Joined: Fri Mar 19, 2010 10:32 am
Location: the depths of hell - also known as AZ


Re: Resin Heads on Obitsu Bodies

Postby K2! » Thu Jan 22, 2015 7:53 pm

Greyhaunt wrote: could I drill a hole like that with a dremel? Do they make drill bits of this type for them?

Yes, it is possible to fit a standard drill bit in a Dremel tool if you have the right parts on the business end of your Dremel.
Does your Dremel tool have a standard collet or an adjustable chuck like a drill?
http://www.mini-lathe.org.uk/collets_ho ... shop.shtml
Collets usually have two parts, an inner part that the Dremel bit slips in (the collet) and ring /collar that tightens down on the assembly (the collet nut). Collets are usually made to fit one size of shaft so you would have to change the collet to accommodate smaller or larger shafts. The shafts of Dremel tool bits come in standard sizes.
http://www.dremel.com/en-ca/Accessories ... x?pid=4485
You change the collet on your Dremel to fit the shafts of various sized tip shafts. If you have a collet that the drill bit fits snuggly into and the collet nut tightens down on it, you're good to go.
If the drill bit of choice doesn't fit in the collets you have, you might need a pin vise that fits in your collet or a pin chuck (a small version of the chuck on a standard drill) to replace your collet entirely.
http://www.exisle.net/mb/uploads/monthl ... 412998.jpg
Image
User avatar
K2!
Stoopid Noob
 
Posts: 2648
Joined: Sat Mar 20, 2010 6:31 pm
Location: The Angry Dome


Re: Resin Heads on Obitsu Bodies

Postby ShortNCuddlyAm » Fri Jan 23, 2015 7:36 am

If the drill bit is a little too small for the collet, you can pad it with masking tape - just wrap masking tape around the part that goes in the collet until it's thick enough (sticky side on the drill bit!). You need to make sure the masking tape is actually sticking to the bit, otherwise it'll still just fall out...
Remember, the reverse of stressed is desserts.
Growing older is mandatory. Growing up is optional.
User avatar
ShortNCuddlyAm
Dolliehs Consume My Brains
 
Posts: 1266
Joined: Sun Nov 11, 2012 9:42 am
Location: London, near enough (UK)


Return to Board index

Return to Tutorials

Who is online

Users browsing this forum: No registered users and 2 guests